Workshop and mobile-mechanic setup

Electrical

Fluke 88V/A Kit

88V/A automotive multimeter combo kit

An automotive multimeter kit for electrical fault-finding at sensors, wiring, batteries and other vehicle circuits. The supplied probes and accessories matter as much as the meter when deciding whether the kit suits your diagnostic work.

Check that the offer includes the automotive kit accessories, rather than the meter alone. Training and the correct leads remain essential; the CAT rating alone does not establish suitability for EV traction-battery work.

Electrical

Clore Automotive BA9

SOLAR BA9 battery and system tester

A battery and system tester for checking starting batteries and investigating charging or cranking concerns. Use the correct battery type and rating settings before interpreting a result.

Requires a starting-battery rating such as CCA/CA; not a general lithium or high-voltage traction-battery tester.

Electrical

NOCO GB40

Boost GB40 portable jump starter

A portable jump starter for starting assistance when a vehicle battery cannot supply enough cranking power. It belongs in a roadside or workshop recovery kit alongside equipment that can investigate why the battery went flat.

Match the battery type and engine application. Confirm the selected hardware revision and supplied charging cable before ordering.

Electrical

NOCO GENIUS5

GENIUS5 smart charger and maintainer

A compact charger and maintainer for compatible vehicle batteries during storage or workshop downtime. Choose the charging mode for the battery chemistry and condition rather than treating every 12-volt battery alike.

Select the mode for the actual battery chemistry; a charger is not a jump starter. Confirm US mains version and connector bundle.

Electrical

NOCO GB70

Boost HD GB70 12V jump starter

A larger jump-starting option for suitable vehicles beyond the GB40’s stated engine applications. Compare its size and engine rating with the vehicles you actually service before choosing the higher-output unit.

Peak current is not a battery-health diagnosis. Check the battery type, vehicle application and supplied hardware revision; this is a GB70 jump starter rather than a GENIUS charger.

Power tools

Milwaukee 2962-20

2962-20 M18 FUEL 1/2-inch mid-torque impact wrench

A cordless impact wrench for repeated removal and run-down of suitable vehicle fasteners. Budget separately for the battery system, impact-rated sockets and a torque wrench for final tightening.

Battery and charger are separate. Breakaway torque does not establish final fastener torque; finish with a calibrated torque wrench to the vehicle specification.

Power tools

Milwaukee 2567-20

2567-20 M12 FUEL 3/8-inch high-speed ratchet

A cordless ratchet for turning accessible fasteners quickly once the job is set up. Its head clearance and battery system are more useful buying considerations than treating it as a substitute for an impact wrench.

Battery and charger are separate. Use the powered ratchet to run suitable fasteners, then use the specified manual or calibrated tool for final tightening.

Power tools

DEWALT DCF891B

20V MAX XR 1/2-inch mid-range impact wrench, bare tool

A DEWALT-platform alternative to the Milwaukee M18 mid-torque impact wrench for suitable removal and run-down work. Owning compatible batteries can matter more to the total purchase than a headline torque figure.

Choose the DCF891B hog-ring bare tool, not a detent-pin or battery-kit variant. Use impact-rated sockets and a calibrated torque wrench for specified final tightening.

Lifting

Arcan A20019

3-ton aluminium low-profile floor jack

An aluminium floor jack for raising a vehicle at its approved lifting points before suitable supports are installed. The low-profile design is useful only where its entry height, reach and lift range fit the vehicle.

Use only on a suitable hard, level surface at approved lifting points. Immediately support the vehicle with appropriately selected stands; never work underneath a vehicle supported only by this jack.

Lifting

ESCO 10498-PAIR

10498-PAIR three-ton performance jack stands

A pair of pin-adjusted jack stands for supporting a suitably raised vehicle at approved support locations. Check working height, saddle contact, ground conditions and the manufacturer’s capacity instructions together.

Manufacturer manual requires pair configuration for supporting a vehicle end. Do not turn the per-stand figure into an unrestricted six-ton vehicle recommendation. Match saddle and support point.

Lifting

SUNEX 6602LP

2-ton steel Low Rider floor jack

A low-entry steel jack for suitable vehicles where the Arcan’s entry height or lift range does not fit the lifting task. Compare chassis reach, lifting-point access and handling weight as well as capacity.

Use on a suitable hard, level surface at approved lifting points. Install correctly selected stands before working beneath a vehicle; a jack’s maximum height alone does not establish vehicle suitability.

Fluids

Lisle 17922

17922 multi-drain tub

A broad drain tub for collecting used fluids during suitable oil, transmission, differential or radiator service. Check its footprint and height against the space below the vehicle before ordering.

Check under-vehicle clearance and expected fluid volume/temperature. Used-fluid capture and clean filling require separate containers.

Fluids

Lisle 19752

19752 six-quart oil dispenser, red spout

A dispensing container for transferring the correct service fluid into a suitable fill point. Keeping clean filling equipment separate from used-fluid collection helps avoid contamination.

Keep the dispenser clean and dedicated to compatible fluids. The selected 19752 has a red flexible spout; it is not a used-fluid drain container.

Fluids

Mityvac MV7201

Fluid Evacuator Plus manual extractor and dispenser

A manual extractor and dispenser for compatible fluids and service procedures. It offers a different collection method from a drain tub where the engine or system permits extraction through an appropriate tube.

Confirm the fluid, temperature limits and access method in the instructions. Do not assume extraction removes all fluid or replaces a required drain-plug or filter-service procedure.

Inspection

Streamlight 66118

66118 Stylus Pro penlight, black

A slim penlight for looking into confined engine-bay, cabin and under-vehicle spaces. Its pocket size makes it a useful companion to a larger work light rather than the only lighting in the bay.

A compact black AAA penlight for close inspection. The stated output and runtime are manufacturer figures, rather than our own measurements.

Inspection

Milwaukee 2125-20

2125-20 M12 underhood light, bare tool

A cordless underhood light for illuminating the engine bay during inspection and service. Check the mounting arrangement, vehicle opening and battery requirements before buying the bare tool.

The -20 offer is the bare underhood light. Budget for a compatible M12 battery and charger, and check that the hooks fit the vehicle.

Apprentice hand tools

Ullman Devices HT-2

HT-2 telescoping magnetic pickup tool

A telescoping magnetic pickup tool for retrieving suitable ferrous items from awkward spaces. It is a useful small addition for dropped fasteners that remain visible or can be located safely.

Check that the selected model is HT-2. Its magnetic pickup claim depends on the object and contact conditions and is not a rating for lifting equipment.

Apprentice hand tools

Ullman Devices HTC-2

HTC-2 telescoping inspection mirror, black

A telescoping inspection mirror for viewing behind components and around obstructions. Pair it with a light when a direct line of sight is blocked.

The 2.25-inch round mirror and adjustable head suit inspection behind components. Check collapsed size before choosing it for a small pocket or pouch.

Storage

GEARWRENCH 83151

83151 20-inch three-drawer steel toolbox

A portable drawer chest for organising a smaller mechanic’s hand-tool kit. Check its dimensions and storage layout against the tools you need to carry or keep close to the work.

Portable storage rather than a complete workshop cabinet; account for loaded carrying weight.

Storage

SUNEX 8057XTR

Premium six-drawer service cart, red

A rolling service cart for keeping a larger working tool selection beside the bay. It is a workshop upgrade from the portable GEARWRENCH chest, rather than a substitute for a box that must be carried between sites.

Check freight delivery, assembly, loaded footprint and floor conditions before ordering. Observe the cart and individual drawer load limits and lock the casters during stationary work.

Workshop safety

DEWALT DPG94-1D

Dominator clear-lens safety glasses

Clear-lens safety glasses for suitable indoor workshop tasks. They are the DPG94-1D industrial variant; the exact lens and model should be checked when ordering.

Clear lenses preserve visibility indoors. Match eye protection to the task; safety glasses alone do not cover every grinding, chemical-splash or face-protection requirement.

Workshop safety

3M PELTOR X4A

X4A PELTOR over-head hearing protectors

Headband earmuffs for a workshop hearing-protection kit. Selection depends on noise exposure, fit and compatibility with other protective equipment.

Fit and exposure matter as much as the labelled NRR. These are the X4A headband earmuffs, not a hard-hat attachment.

Workshop safety

MaxxHaul 70472

70472 rubber wheel chocks, two-pack

Rubber wheel chocks for helping restrain an appropriately parked vehicle during suitable workshop work. Match their size and use to the tyre, surface and equipment procedure.

Check the manufacturer’s instructions against the vehicle, surface and intended use. Wheel chocks complement suitable lifting and support equipment; they do not replace jack stands.